There are currently no product reviews.
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
Copy of genuine owners/operators manual, very useful
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimum placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure. The Studio Series S36 loudspeakers are videoshielded and can safely be placed near a television. Although these loudspeakers are designed as a mirrored pair, the decision as to which one is left or right will depend on the amount of space left between them.
Installation of Self-Adhesive Rubber Pads: If the S36 is to be placed on a surface (such as a table top or shelf) rather than being wallmounted, the enclosed selfadhesive rubber pads are to be attached to the bottom of the speaker cabinet in their designated recessed locations. If the S36 is to be wallmounted, then the four selfadhesive rubber pads should be attached to the back of
the speaker, as shown in the bottom right diagram. The S36 can also be used on floor stands. Please see your JBL dealer for more information.
PADS GO HERE
For tabletop or shelf placement
PLACE RUBBER PADS HERE
For stereo-only applications:
Less than 6 â 8 feet
More than 6 â 8 feet
A wider stereo image is presented with the tweeter/midrange array outboard, and a tighter image is presented with the array inboard.
KEYHOLES FOR MOUNTING HARDWARE
speakers identically: (+) on the speaker to (+) on the amplifier and (â) on the speaker to (â) on the amplifier. Wiring âout of phaseâ results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity
For home-theater applications:
This placement provides a wide spread in sound, supplemented by the center-channel speaker.
+ â+ â +
The S36 loudspeakers may be positioned on the wall either horizontally or vertically. The grille logo on each speaker may be rotated depending on how the speaker is positioned. Gently pull the logo away from the grille slightly, rotate it to the desired
position, and let go. The logo will snap back into place. When mounted vertically, the tweeter array may be positioned either up or down, depending on the height of the placement. If the speakers will be above ear level, the tweeter array
should be positioned down, preferably no more than two feet above ear level. If the speakers will be mounted very low, it may be best to position the tweeter array upward so that it will be no more than two feet below ear level.
Speakers and electronics terminals have corresponding (+) and (â) terminals. It is important to connect both
remains equally important in order to preserve the proper ambience and directionality of the program material.
If there is no sound from any of the speakers: â¢ Check that receiver/ amplifier is on and that â¢ Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. â¢ If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is no sound coming from one speaker: â¢ Check the âBalanceâ control on your receiver/ amplifier. â¢ Check all wires and connections between receiver/amplifier and speakers. â¢ Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
The Studio Series S36 loudspeakers may be wallmounted as either front or rear speakers, horizontally or vertically. The S36 enclosures are specially designed to angle the speakers toward the listener when mounted flush against the wall. A template sheet is provided to aid in drilling mounting holes needed for the 4 keyholes on the back of the S36. Always use all 4 keyholes, and try to place at least 2 of the 4 screws into a wooden wall stud. Size 10 screws of at least 1-1/2" in length are recommended. If the screws are used in drywall or other surfaces incapable of holding the screw by itself, selection of proper anchors is essential. The customer is solely responsible for proper selection and installation of screws, anchors and other installation hardware. Further installation details are included on the installation template.
a source is playing. â¢ Review proper operation of your receiver/amplifier. â¢ Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. If the system plays at low volumes but shuts off as volume is increased: â¢ Check all wires and connections between receiver/ amplifier and speakers.
Declaration of Conformity
We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the loudspeaker
described in this ownerâs manual is in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1992
Steen Michaelsen Harman Consumer International France. 5/00
Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…