|
Who's Online
There currently are 5839 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
A comprehensive Operating and Service Manual. All schematics are complete and easy to read. The PCB drawings and complete parts list are very helpful. I would definitely recommend this manual.
;
SCANNING OF HIGH QUALITY
VERY, VERY HIGH VELOCITY DOWNLOAD
VERY GOOD PRICE,
TRUE SATISFIED, THANKS
;
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
;
I purchased a vintage Sony mixer off eBay and within the hour was able to locate and purchase the manual for it.I mean really,where else can you find a manual for a product made in 1983!? It was easy to find and purchase/download the manual I needed.I will use this site again for other equipment I have! Great site!
;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
Gently pull the slack out of the wire and screw the adaptor onto the back of the speaker in two places, as shown. The floor stand adaptor screws may be found in Hardware Bag B. Use the larger screw in the upper screw hole, and the smaller
screw in the lower screw hole. Screw the floor stand adaptor into the floor stand�s threaded insert until the speaker is firmly attached to the stand. Back off slightly from the fullytightened position until the speaker is oriented as desired, then rotate the thumbwheel at
the bottom of the floor stand adaptor to secure the speaker to the stand.
WALL-MOUNTING
4 3 2
7 6
1
1
2 3 4
8 5
5 8
Important Safety Note: The customer is solely responsible for proper selection of mounting hardware not included with the speakers, and for proper assembly and installation of the wallbrackets, including but not limited to the selection of appropriate weight-bearing supports and proper use of the bracket. JBL disclaims any liability for the selection of mounting hardware and/or bracket installation. Be sure to follow these bracket assembly and installation instructions carefully. If you have any questions or doubts about your ability to correctly wall-mount the speakers, consult with your authorized JBL dealer or custom installer. Step 1: Unscrew and remove the large Molded Nut �. If necessary, use the supplied Metal Bar � as a lever by
6
inserting it into one of the holes in the outer edge of the Molded Nut �. Step 2: Firmly grasp the Ball and Shaft £ and pull it straight out of the Attachment Plate ¢. Avoid leaning it to the side for leverage, as this may break off a tab. Step 3: Slide the Molded Nut � onto the Ball and Shaft £ with the threaded opening facing the ball. Thread the Metal Nut ¡ all the way onto the Ball and Shaft £, with the star washer side away from the ball. Refer to the exploded drawing for the proper orientation of these parts. Step 4: Screw the Ball and Shaft £ into the Threaded Insert § on the back of the Satellite Speaker ¶ until it is fully seated in the Threaded Insert §, but do not tighten as you might dislodge the Threaded
Insert §. Such damage would not be covered under the warranty. Step 5: Tighten the Metal Nut ¡ with the star washer side between the Metal Nut ¡ and the back of the Satellite Speaker ¶, using large needle-nose pliers, until it is firmly seated against the back of the Speaker ¶ and has locked the Ball and Shaft £ and the Satellite Speaker ¶ together. Note that once the Metal Nut ¡ is fully tightened, it may embed some marks on the back of the Satellite Speaker ¶. However, these marks will be covered by the Metal Nut ¡. Step 6: Mount the Attachment Plate ¢ into a wood stud on the wall, using four #10 pan-head wood screws at least one inch long (not supplied) �. Make sure that all four screws are driven
|
|
|
> |
|