Shopping cart is empty
English Polski Spanish 
Search For a Manual

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
Who's Online
There currently are 527 guests online.
Featured Product
Home >> JBL >> TLXPS12 Service Manual
 0 item(s) in your cart 

Service Manual

Tweet about this product and get $1.00 of store credit for instant use!
  • Contains Circuit Diagrams
  • Download
  • PDF Format
  • Complete manual
  • Language: English
Price: $4.99

Description of JBL TLXPS12 Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagrams, printed circuit boards, repair tips, wiring diagrams, block diagrams and parts list. Service Manual ( sometimes called Repair Manual ) is used mainly by technicians.

If You just want to know how to use Your tv, video, mp3 player etc. You should look for Owner's Manual. After placing order we'll send You download instructions on Your email address.

The manual is available in languages:

Not yet ready
You must purchase it first

Customer Reviews
There are currently no product reviews.
Other Reviews
 A501 BRAUN Service Manual by Thomas Nehls;
It's the manual, I am searching for. Now I am able to repair my Braun A501.
 PM5131 PHILIPS Service Manual by Thomas Nehls;
Great service manual. Unfortunately on page no. 41 there are some details which i can't read.
 PS-FL7II SONY Service Manual by Gerald Levitz;
Wonderful service... doubt that I could have made the repairs to my turntable without this service manual. Great help! Well worth the price paid!
 DFS-700P SONY Service Manual by MILTIADES BEAZER;
nice completed SERVICE MANUAL as the description THANK YOU !!!-
 VSX453 PIONEER Service Manual by Louie Role;
The service manual is as described and received the link to the download sooner than expected. Great service, quality product. This site is a big help in the electronics repair business.

Text excerpt from page 7 (click to view)
Powered Subwoofer


pliers, gently heat and remove cut lead from hole in edge or PCB. Clean insulator and seating area on back of panel. Coat both sides of insulator with silicon (white) thermal compound (unless silicone rubber pads are provided), position it centered on back of device with holes aligned. Insert leads into PCB then place pair over hole in panel; ensure hole in insulator is aligned. Insert screw from far side, pass shoulder bushing over screw and carefully seat shoulder in hole in tab, add flat washer, lock washer and nut (finger tight). Center insulator tighten screw first then solder all three leads in respective slots with full fillet, being careful not to bridge pads. Use ohmmeter to verify there is no short from tab of transistor to panel, or between pads.

Connect sub-woofer system to a music source. Play at high level while checking for air leaks around panel edge, driver, panel jacks and controls, and voice coil problems such as rubbing or loose turns. With the crossover "frequency" set to 50Hz, very little of the voice content should be heard.

F1 Fuse SLOW BLO 2.0A 250v GMC 20mm UL approved. Fuse holder. Use only factory replacement.


PWR CORD SPT-2 better with polarized plug, UL appoved wired with the hot side to fused side. Use with UL approved panel strain relief only. Never operate amplifier with load connected when PC assembly is not attached to panel or when any of output transistors is not properly screwed to panel. After repair, inspect for possible safety hazards, including loose hardware, missing lock washers, correct fuse and lead dress of primary wires (these must be held in position with cable ties so that they cannot touch secondary components). With ohmmeter, check that panel is connected to signal ground. XF transformer. use only factory replacement. Bridge diode. Use only factory replacement. 6800uF, 63V electronic filter caps. Be sure replacement part is at least the same working voltage and capacitance rating. Also the lead spacing is important. Incorrect spacing may cause premature failure due to internal cabinet pressures and vibration. K1 It is essential that the following safety insulation test be performed prior to returning the Power Sub-Woofer to the customer, using one of the following methods: A) Insulation Resistance Test With a 500VDC Insulation Tester, Check insulation from the outer metal contact of the RCA jack (chassis) to the line neutral of AC cord. Resistance should be >100Mâ¦. B) Hi-Pot Test If a UL approved Hi-Pot tester is available, test line & neutral of AC cord to outer shell of RCA jack (chassis) at 1100VAC for 2 seconds. Observe all of instrument manufacturer's instructions and safety warnings in performing this test. Safe operating area relay to protect output devices. Use only factory replacement. 5.6⦠.5W METAL FILM, non flammable.


C36, 37



You might also want to buy


Owner's Manual

Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
Parse Time: 0.289 - Number of Queries: 107 - Query Time: 0.056